SYNTHETIC RESIN: products

LOOK – SELECT – ORDER

THE ORDER FORM IS AT THE VERY BOTTOM

CHOCKFAST orangeCHOCKFAST orange in applicationCHOCKFAST orange in applicationCHOCKFAST orange in application

 

CHOCKFAST orange

Low-viscosity 2-component epoxy resin. Used as a cast-in-place spacer, especially in the naval sector. Very good adhesion to steel. Layer thicknesses of 12 – 100 mm.

Safety Data Sheet (PDF)
CHOCKFAST orange

     

CHOCKFAST red

 

CHOCKFAST red

3-component epoxy resin, suitable for full-surface cast-in-place footings of large plants, e.g. compressors and turbines, with single layer thicknesses of 50 – 460 mm.

CHOCKFAST red is also suitable for repairing damaged foundations.

Safety Data Sheet (PDF)
CHOCKFAST red
     
CHOCKFAST red SGCHOCKFAST red SG in applicationCHOCKFAST red SG in applicationCHOCKFAST red SG in application  

CHOCKFAST red SG

3-component epoxy resin, suitable for full-surface cast-in-place footings of large plants, e.g.  compressors and turbines, with single layer thicknesses of 25 – 100 mm.

CHOCKFAST red SG is particularly free-flowing and is also suitable for repairing damaged foundations.

Safety Data Sheet (PDF)
CHOCKFAST red SG
     
CHOCKFAST red HF  

CHOCKFAST red HF

3-component epoxy resin, suitable for full-surface cast-in-place footings of large plants, e.g.  compressors and turbines, with single layer thicknesses of 25 – 100 mm.

Due to its especially high fluidity, CHOCKFAST red HF is pumpable and therefore suitable for plant that is particularly inaccessible for structural reasons.

The castable resin products we offer can also be cast in several layers to meet the requirements for larger layer thicknesses.
     

CHOCKFAST blackCHOCKFAST black in applicationCHOCKFAST black in der Anwendung

 

CHOCKFAST black

2-component epoxy resin. Used as a cast-in-place spacer on frames under hot machines to achieve ventilation below machines through the use of spacers, or to lower the foundation temperature. Layer thicknesses of 32 – 62 mm. 

Safety Data Sheet (PDF)
CHOCKFAST black

     

CHOCKFAST grayCHOCKFAST gray in applicationCHOCKFAST gray in applicationCHOCKFAST gray in application

 

CHOCKFAST gray

2-component epoxy resin, resists oils, chemicals and high temperatures, used as a new casting or for repairs in corrosive environments. Layer thicknesses of 12 – 50 mm. 

Safety Data Sheet (PDF)
CHOCKFAST gray

     
Phillymastic TG 7B (Härter) von Philadelphia Resins  

Phillymastic TG 7B

Phillymastic TG-7B is a two-component epoxy resin specifically for bedding LNG and LPG tanks in ships’ hulls. In this type of installation the tank is supported on wooden insulation blocks. Phillymastic TG-7B offers excellent properties in terms of adhesion characteristics and good load-bearing capability at cryogenic temperatures, and ensures uniform load distribution in the installed tanks. It is available either as a pourable liquid or trowellable paste, and both can be mixed either by hand or mechanically.

Safety Data Sheet (PDF)

Phillymastic TG 7B Hardener

Phillymastic TG 7B Resin

Phillymastic TG 7B Liquid Hardener

Phillymastic TG 7B Liquid Resin

     
Chockfast red und red SG Aggregate  

AGGREGATE FOR
CHOCKFAST red and red SG

Aggregate for the 3-component epoxy resins CHOCKFAST red and CHOCKFAST red SG.

Safety Data Sheet (PDF)

Aggregate for CHOCKFAST red
Aggregate for CHOCKFAST red SG
     
Chockfast red HF Aggregate  

AGGREGATE FOR
CHOCKFAST red HF

Aggregate for the 3-component epoxy resin CHOCKFAST red HF.
     
Socketfast  

Socketfast

Epoxy resin
Manufacturer: ITW Polymer Technologies

     
Phillybond No. 6  

PHILLYBOND No. 6

High temperature resistant 2-component epoxide paste
Manufacturer: ITW Polymer Technologies

     
Phillybond orange  

PHILLYBOND orange

Elastic 2-component epoxy resin
Manufacturer: ITW Polymer Technologies

     
Repair Compound   

Repair Compound

2-component epoxy resin for repairing areas of damage
Manufacturer: ITW Polymer Technologies

Safety Data Sheet (PDF)
Repair Compound Hardener

Repair Compound Resin

     
Casting heights depend on the environmental conditions, among other things.
     
     
     

PRODUCTS USED WHEN CASTING CHOCKFAST:

WE WILL GLADLY ADVISE YOU ABOUT THESE

Rubber slabs  

Rubber slabs

To construct insulation and expansion joints

Length: 1,000 mm
Width:       20 mm
Height:      20; 25; 30; 35; 40; 50;
                  60; 70 mm
     
Rubber sleeving  

Rubber sleeving

To shield anchor bolts and for sealing holes

Outer diameter:
20 – 53 mm



     
Terostat IX  

Terostat-IX

Kneadable sealant (gray)
Manufacturer: Terostat

     
Non-stick spray for CHOCKFAST orange  

Non-stick spray
for CHOCKFAST orange

Release agent for easy removal of formwork
Manufacturer: Rocol
     
Non-stick spray for CHOCKFAST red  

Non-stick spray
for CHOCKFAST red

Release agent for easy removal of formwork
Manufacturer: WINIX

     
Alvania EP (LF) 2 by Shell  

Alvania EP (LF) 2

Grease as release agent
Manufacturer: Shell

     
Sealant composition by Simson  

Sealant composition

To seal expansion joints
Manufacturer: Simson

     
Armaflex by Armacell   

Armaflex

Adhesive tape for vibration insulation
Manufacturer: armacell

     
Armaflex 520  

Armaflex 520

Adhesive to construct formwork made of rubber sheets
Manufacturer: armacell

     
Special silicone – neutral by Otto Chemie  

Special silicone – neutral

Silicone to seal insulation
Manufacturer: Otto Chemie

     
Epoxy resin mixer  

Epoxy resin mixer

Metal mixer to mix epoxy resins, e.g. CHOCKFAST
     

INJECTION MATERIALS USED WHEN CASTING EPOXY INJECTION RESIN:

WE WILL GLADLY ADVISE YOU ABOUT THESE

WEBAC Injection resin 4170T component A and B  

WEBAC Injection resin 4170T component A and B

Suitable for crack injections, foundation refurbishment of wind turbines and repair of oil contaminated and moist cracks.
Manufacturer: WEBAC

Safety Data Sheet (PDF)
WEBAC Injection resin 4170T component A (DE)
WEBAC Injection resin 4170T component B (DE)

Technical Data sheet (PDF)
WEBAC Injection resin 4170T (EN)

     
WEBAC Injection pump incl. injection hose and female zerk coupler  

WEBAC Injection pump
incl. injection hose and female zerk coupler

Special hand pump with high pressure reinforcedhose and female zerk coupler for sealing and injection work with epoxy injection resin.
Manufacturer: WEBAC

     
WEBAC Injection packers for epoxy resins  

WEBAC Injection packers

Injection packers are filler necks, that serve as connection pieces between building component and injection device, e.g. when sealing building structures or repairing cracks.
Manufacturer: WEBAC

     


WOULD YOU LIKE TO PLACE A DIRECT ORDER?

We have created an order form for you. All you need to do is fill it in and return it to us.

Please send it to us by Fax to +49 (0) 40 - 25 155-150 or by e-mail to plambeck@mim-hamburg.de.

Download order form